Features:

• • Genuine Remote for Merlin Garage Door : Codes both Merlin Security+ and Security+ 2.0 on the same remote
  • IP65 Waterproof & Dustproof: Fully protected against dust and resistant to low-pressure water jets.
  • Enhanced Security: Rolling code technology with over 100 billion unique codes.
  • Multi-Device Control: Operates up to four Merlin openers or gates.
  • Long Battery Life: Powered by a CR2032 lithium battery (included).
  • Free Shipping: Enjoy free shipping and a 2-year manufacturer’s warranty on your purchase.

*IP65 rating – full protection against dust and other particles as well as protection against low-pressure jets (6.3 mm) of directed water from any angle.

Includes:

• Brand New Genuine Merlin Remote
• CR2032 Lithium Battery
• Keyring Carabiner Attachment
• Coding Instructions

Compatibility:

This remote is compatible with a wide range of Merlin garage door openers, including:

• Commander Series: Commander Essential (MS65MYQ), Commander Elite (MS105MYQ), Commander Extreme (MS125MYQ), Commander Ultimate (MJ3800MYQ)
• SilentDrive™ Series: SilentDrive Essential (MR655MYQ), SilentDrive Elite (MR855MYQ)
• Other Models: WhisperDrive, TiltMaster, PowerAce, CyclonePro, OverDrive

It also works seamlessly with genuine Merlin receivers such as the E8003M Tri-Channel Receiver, E860 Weatherproof Receiver, and CM8002ANZ, as well as genuine Merlin wall button remotes like CM128, E128M, E138M, and E148M.  The Merlin receivers were also built in to some Steel Line motors – ST50-EVO.

If you are currently using one of the below remotes this remote is compatible with your opener.

• Merlin C945
• Merlin C943
• Merlin CM842/4
• Merlin E945M
• Merlin E950M
• Merlin E960M
• Merlin E970M
• Merlin E943M

The Merlin E980M Waterproof Remote is a next-generation, genuine Merlin 4-button remote designed to offer robust and durable control for your Merlin garage door openers. With an IP65 water and dust resistance rating, this remote is built to withstand tough conditions while providing seamless operation.

Featuring compatibility with both Merlin Security+ and Security+ 2.0 systems, the Merlin E980M allows you to control up to four powered garage doors or gates. Each use generates a unique rolling code for enhanced security, making it nearly impossible to clone. The remote also includes an LED indicator that flashes green upon activation, providing clear visual confirmation.

This model is compatible with any Merlin garage door opener manufactured since 2009 and includes a keyring carabiner for easy attachment. With its long-range frequency and ergonomic design, the Merlin E980M is perfect for anyone looking for reliable, convenient access to their garage or gate.

Frequently Asked Questions

WARNING! KEEP BATTERIES OUT OF REACH OF CHILDREN. Never allow children to replace button batteries on any device. Swallowing or placing inside any part of the body may lead to severe or fatal injuries in as little as 2 hours or less due to chemical burns and potential perforation of the oesophagus.

If you suspect your child has swallowed a button battery or placed inside any part of the body immediately call the POISONS INFORMATION CENTRE on 13 11 26 for prompt advice. If your child is having any difficulty breathing, contact 000.

Dispose of used button/coin batteries immediately and safely. A battery can still be dangerous even when it can no longer operate the device. Place sticky tape around both sides of the battery and dispose of it immediately out of reach of children in an outside bin or recycle safely.

Please see button battery safety information from the Australian Competition & Consumer Commission (ACCC).

Merlin E980M Programming Instructions

The Merlin E980M Remote is versatile, allowing programming for both Merlin Security+ and Security+ 2.0 codes. With four available buttons, any button can be programmed for either code.

Preparation:

• Locate the LEARN button on your garage door opener.
• Identify the button on the remote you wish to program. Make sure not to select a button already in use.

For Merlin 2.0+ Series (Preset for Security+ 2.0):

If you are using an EVO model with Security+ 2.0, the remote is preset for this system.

To program:

1. Initiate Programming:
   • Press and hold the button on the remote you wish to use.
   • Press and release the LEARN button on the garage door opener.
2. Confirm Code Learning:
   • Release the remote button when the opener light flashes, confirming the code has been learned.
   • Test the remote by pressing the programmed button; it should activate the door.

Note: If you are unsure of the previously set code, try the Security+ programming sequence outlined below.

For Merlin+ Series (Security+ Programming Sequence):

For older Merlin+ systems, follow these steps to program:

1. Enter Programming Mode on the Remote:
   • Press and hold the left and right buttons on the remote simultaneously for about 5 seconds.
   • Release when the LED on the remote remains continuously ON.
2. Program the Remote:
   • Briefly press and release the LEARN button on your garage door opener.
   • Within 30 seconds, press the button on the remote that you wish to program.
3. Confirm Code Learning:
   • If the opener light flashes, the code has been learned. If it doesn’t flash, press the selected button again until the light flashes.
4. Lock in the Code:
   • Press any one of the other three buttons on the remote to lock in the code. The remote LED should turn OFF.
5. Test the Remote:
   • Press the programmed button. The garage door should activate. If it doesn’t, repeat the process.

Returning to Security+ 2.0:

• To switch back to Security+ 2.0 for a button, simply repeat the initial programming sequence.