Features:

• Genuine original equipment remote
• Advanced Code-Hopping Technology
• Free standard shipping Australia-Wide*
• 2 Year Manufacturers Warranty*

Includes:

• Brand New Remote
• 1 x Battery
• Coding Instructions
• Keyring Attachment
• Belt Attachment

Compatibility:

This remote is only compatible if your remote looks identical or identical with variation in button design 1,2,3 buttons and will either have multiple colours or all BLUE buttons.

• Centsys Nova ONLY

Motors:

• D2 Turbo (Sliding)
• D3 (Sliding) – must use remote with blue buttons not green
• D5 (Sliding) – must use remote with blue buttons not green
• D5 Evo (Sliding)
• D10 (Sliding)
• D10 Turbo (Sliding)
• A10 (Sliding)
• R3 (Rotary Arm)
• R5 (Rotary Arm)
• Vantage 400 (Swing)
• Vantage 500 (Swing)
• Vector 2 (Swing)
• Vector 400 (Swing)
• Vector 500 (Swing)
• Vert-X 300 (Swing)

Not compatible with the Censys Smart remote (also known as Centurion Gates Smart Remote) with GREEN buttons.

Offering advanced code-hopping technology means every code transmitted by this remote is totally unique.  Preventing unwanted copying of your remote signal and cloning of the remote itself.  The NOVA remote offers the same level of security as currently provided by leading brand automobile manufacturers for immobilising vehicle alarms and activating door locks.

Programming Instructions for CENTSYS Nova Remote

Programming Instructions for Centsys for D-Series Motors

Coding via APP (D5, D10 SMART)

You will need to download the MyCENTSYS Pro app to program new remotes.

Watch this handy video for instructions on how to sync and add new remotes to your Centsys SMART opener.

Coding via EVO Receiver (D5 and D10 EVO/TURBO

Press the OK button for 2 seconds to enter “Programming.” Press the Down arrow to scroll to Remote Controls (TX). Press OK to select Add Remote. Press OK again to Select Function Trigger Gate. Press OK to select Time Bar Remote?. Press OK to proceed to Press Remote Button. Press any button on your new remote you wish to activate the gate for 2 seconds. The LED screen will display SUCCESS. Press the EXIT button twice to exit programming mode.

Coding via Turbo Rotary Dials (D2 Turbo)

Rotate the Function Dial to the REMOTES position. Rotate the Settings Dial to the TX TRG selection. Press the STATUS Push Button (Select or Enter). The Status LED will change from red to green, confirming the current setting. Press any button on the new remote you want to operate the gate. The LED will flash twice, and the onboard buzzer will pulse twice to confirm the remote has been learned. Return the Function Dial to the RUN position.

Programming via Helix Single or Multi Receiver

• Open the receiver unit and locate the Learn jumper pins
• With the power on, bridge the Learn/J1 pins. The red LED will illuminate.
• Press the required button on the new remote. The red LED will flash once, indicating successful programming.
• Repeat this process for any additional remotes.
• Remove the jumper from bridging and store it on one of the two pins.

Deleting Remotes via Helix Receiver

1. Start with the receiver powered on.
2. Fit a link bridging J2 and the common (middle) pin. The LED will flash 10 times, indicating it’s about to enter the erase procedure.
   • Note: Removing the link during the flashing stage will cancel the erase operation.
3. After the LED flashes 10 times, it will stay on.
4. Remove the link across J2 and the middle pin to complete the erase operation. The LED will switch off once memory is erased.

Lost Master Remote

1. The master remote is identified by a red LED that gives one long flash and then one short flash when any button is pressed.
2. If the master remote is lost, you’ll need to erase all memory and reprogram a new master remote. All existing remotes will need to be reprogrammed afterward.